The traction baler is the main agricultural machinery for the comprehensive utilization of straw in the operation of agricultural machinery. The machine needs to be pulled by a tractor, and the required power is provided by the power output shaft of the tractor. The baler is mainly used to collect and pack wheat and other crops and put them on the straw in the field. In order to prevent farmers from burning straw to pollute the environment and increase farmers’ economic income, corn straw is easier to bundle and sell, which is conducive to the rational use of resources.
How to clean the baler after use?
1. Use it several times, and then soak it in the sprayer 2 to 24 hours 2 to 3 times.
2. Mud and water cleaning: The sweeping light will be dulled and lose its effect on the soil. Therefore, after the battle, you only need to clean the sprayer with mud and water several times, and then rinse with water.
3. Ferrous sulfate scrubbing: Only 24-D butyl ester in the herbicide is difficult to clean. After spraying, it is necessary to use 0.5% ferrous sulfate solution to scrub, and then conduct a safety test before using other herbicides.
The straw baling and wrapping machine can not only effectively complete the automatic picking of straw, but also complete various processes through transportation, compression molding, baling and knotting. It can also bundle scattered straw into regular straw bales, thus greatly reducing the use and consumption of manpower and improving the efficiency of baling.
If you want to use the equipment for a long time, you must do a good job of daily cleaning. Next, I will introduce to you the cleaning method after the baler is used and the method of removing oil stains on the surface of the equipment.
Straw baler cleaning method:
1. Mud and water cleaning: Gramoxone (commonly known as a sweep) will be passivated and lose its efficacy when it encounters soil. Therefore, after spraying, just use mud and water to clean the sprayer several times and then wash it with water.
2. Ferrous sulfate washing: Among the herbicides, only 24-D butyl ester is difficult to clean. After spraying, it needs to be fully washed with 0.5% ferrous sulfate solution and then safety tested before other herbicides can be installed for use.
3. Cleaning with clean water: wheat field herbicide Giant Star (bensulfuron), corn field herbicide Ethyl A mixture, soybean and peanut herbicides such as Gaicaoneng, rice field herbicides Shenchu, Bentazone, etc. need to be cleaned with clean water immediately after finishing the barrel and the parts of the silage baling and film wrapping machine several times, then fill the sprayer with clean water and soak it for 2 to 24 hours, clean it 2 to 3 times, and then you can use it with confidence.
Before operating the straw baler, the corn straw baler must be inspected and adjusted according to regulations, and it can be operated only after it meets the requirements.
1. The moving and fixed blades of the straw baler should always be sharp, otherwise they should be removed and sharpened in time;
2. The bearings on both sides of the main shaft and the bearings on both sides of the feeding roller have been greased during installation, and the straws have been tied. After the machine has been used for 1 month, the above bearings need to be removed, cleaned, and re-applied with grease (good quality butter), and then installed and used. Lubricate the straw baler once a month after operation. Secondly, other rotating parts should also be lubricated with oil frequently during use;
3. Check whether the various parts of the straw baler are severely worn or loose, especially the working parts and rotating parts. If damage, severe wear, looseness, etc. are found, the straw baler should be replaced, repaired and tightened in time. Avoid major accidents; When the corn straw baler is out of use, the dust and dirt on the surface should be wiped off. If the straw baler is parked in the open air, it should be covered with a tarpaulin to prevent the machine from rusting.
The use of the fully automatic baler corn straw baler should pay attention to controlling the durability and adaptability of the product. Secondly, to measure the productivity of the machine, the consumption of energy and raw materials is also a special point.
The initial investment of the fully automatic baler corn straw baler is to consider auxiliary costs such as transportation, insurance, and purchase fees. These comprehensive costs as a whole, the equipment selection of the machine is to consider the model, and these issues should be considered from an economic perspective.
Three solutions are proposed for the phenomenon that the baler cannot start normally:
1. Check whether the power connection is normal, whether the socket, plug, and power cord have oxygen, fall off, or breakage, and solve them accordingly.
2. When the motor does not rotate when powered on, and the wheel can be rotated by lightly turning it by hand, it can be determined that one of the two starting capacitors of the machine has failed. In this case, only a new round baler can be replaced.
3. When the motor does not rotate when powered on, it can rotate when external force is applied, but a weak current sound is emitted in the motor, which is caused by a slight leakage of the starting capacitor. If the current sound is too loud and the motor cannot start at all, it can be determined that the starting capacitor is short-circuited or the motor coil is short-circuited, which generally requires professional repair.
Therefore, when the silage baler cannot start during use, we can check from the above three aspects to find out the cause of the fault, solve it in time, and ensure the smooth progress of the work.
We are a professional agricultural machinery manufacturer with more than 10 years of export experience. We provide you with free product solutions and high-quality agricultural machinery. If you need agricultural machinery, please feel free to contact us at 008613644001762/info@vbesty.com